清洗通风管道这些方法要用上！

发布人：   发布时间：2021-08-12 16:51:43

一。机器设备及专用工具搬到选定地址，并拿布遮盖好施工点下边的物件。

One. Move the machinery, equipment and special tools to the selected address, and cover the objects under the construction site with cloth.

第二。将需清洁的空调风管系统分成数个清洁施工段，明确施工切入点，用电剪切割机切下500×400毫米的开口。

Second. Divide the air conditioning duct system to be cleaned into several cleaning construction sections, clarify the construction entry point, and cut 500 pieces with an electric shear cutter × 400 mm opening.

第三。用气囊塞入清洁管段两边后对气囊充气，气囊规格适宜管道尺寸并产生完善的封闭，充分的隔离清洁区和非清洁区，防止二次环境污染。

Third. Insert the air bag into both sides of the cleaning pipe section and inflate the air bag. The specification of the air bag is suitable for the pipe size and produces a perfect closure. Fully isolate the clean area and non clean area to prevent secondary environmental pollution.

眉山通风管道眉山通风管道

Meishan ventilation duct Meishan ventilation duct

第四。将清洁施工段中间的每个出风口封堵，只留与两边隔开气囊接近的2个出风口。

Fourth. Block each air outlet in the middle of the cleaning construction section, leaving only two air outlets close to the separated airbags on both sides.

第五。将以上所述2个出风口百叶与其他出风口百叶一块儿开展清洁，并装上各自配有吸尘器接口。压缩空气管穿孔与监测器线越过孔的封板。

Fifth. Clean the above two air outlet louvers together with other air outlet louvers, and install them with vacuum cleaner interfaces. The compressed air pipe is perforated and the monitor line crosses the sealing plate of the hole.

第六。将清洁风管段堵上，很多不必要出风口孔洞用其他板材与风管底边暂时补平，以便清洁机器人能在眉山通风管道内圆满通过。

Sixth. The cleaning air duct section is blocked, and many unnecessary air outlet holes are temporarily leveled with the bottom edge of the air duct with other plates, so that the cleaning robot can pass through the Meishan ventilation duct successfully.

第七。将配有清洁毛刷和监测器探头的机器人或有高压空气接管的高压双向喷头，从清洁管段的运行孔放进风管内。

Seventh. Place the robot equipped with cleaning brush and monitor probe or the high-pressure two-way nozzle with high-pressure air connection into the air duct from the running hole of the cleaning pipe section.

第八。打开压缩空气机和吸尘器，使其有旋转毛刷的机器人或高压空气喷头对风管内壁由近而远开展刷喷清洁，依据监测器探头操纵机器人作业。当风管管径不大于３００×１５０mm时，机器人没法进到时由高压喷头或软轴毛刷开展清洁，清洁同时开展全过程录影。

Eighth. Turn on the compressed air machine and vacuum cleaner, make the robot with rotating brush or high-pressure air nozzle clean the inner wall of the air duct from near to far, and operate the robot according to the monitor probe. When the diameter of air duct is no more than 300 × When the robot cannot enter at 150mm, the cleaning shall be carried out by high-pressure nozzle or flexible shaft brush, and the whole process video shall be carried out at the same time.

第九。对圆型风管与螺旋圆风管及其方圆型弯头，都能够用机器人监测器，高压喷头，喷枪替换运用开展清洁。

Ninth. For round air duct, spiral round air duct and its square and round elbow, robot monitor, high-pressure nozzle and spray gun can be replaced for cleaning.